Bunn Dual TF User Manual Page 26
- Page / 47
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 26
Location:
The level control board is located inside the
front of the brewer just left of center on the component
bracket
Test Procedure:
1. Disconnect the brewer from the power source.
2. Remove the violet wire from terminal 1 & pink wire
from terminal 4 of the circuit board.
3. Check the voltage across terminals 2 & 3 with a
voltmeter. Connect the brewer to the power source.
The indication must be:
a.) 120 volts ac for three wire 120/208 volt mod-
els and three wire 120/240 volt models.
b.) 200 to 240 volts ac for two wire 200 or 240 volt
models.
4. Disconnect the brewer from the power source.
If voltage is present as described, proceed to #5.
If voltage is not present as described, refer to the
wiring diagrams and check the brewer wiring harness.
5. Reconnect the violet wire to terminal 1.
SERVICE (cont.)
LEVEL CONTROL BOARD AND LEVEL PROBE
(Electro/mechanical only)
6. Carefully connect a piece of insulated jumper wire
to terminal 4. Keep the other end of this wire away
from any metal surface of the brewer.
7. Check the voltage across terminals 1 & 3 with a
voltmeter. Connect the brewer to the power source.
The indication must be:
a.) 120 volts ac for three wire 120/208 volt mod-
els and three wire 120/240 volt models after a
delay of approximately 1 second.
b.) 200 to 240 volts ac for two wire 200 or 240 volt
models after a delay of approximately 1 sec-
ond.
8. Touch the free end of jumper wire to the brewer
housing. The indication must be 0.
9. Move the jumper wire away from the brewer
housing. The indication must again be:
a.) 120 volts ac for three wire 120/208 volt mod-
els and three wire 120/240 volt models after a
delay of approximately 1 second.
b.) 200 to 240 volts ac for two wire 200 or 240 volt
models after a delay of approximately 1 sec-
ond.
10. Disconnect the brewer from the power source and
remove the jumper wire from terminal 4.
If voltage is present as described, the level control
board is operating properly, proceed to #11.
If voltage is not present as described, replace the level
control board.
11. Reconnect the pink wire to terminal 4.
12. Gently pull the probe out of the tank lid and inspect
for corrosion. Replace it if necessary.
13. Place the probe so that neither end is in contact
with any metal surface of the brewer.
14. Check the voltage across terminals 1 & 3 with a
voltmeter. Connect the brewer to the power source.
The indication must be:
a.) 120 volts ac for three wire 120/208 volt mod-
els and three wire 120/240 volt models after a
delay of approximately 1 second.
b.) 200 to 240 volts ac for two wire 200 or 240 volt
models after a delay of approximately 1 sec-
ond.
15. Move the probe's flat end to the brewer housing.
The indication must be 0.
16. Move the probe's flat end away from the brewer
housing. The indication should again be
a.) 120 volts ac for three wire 120/208 volt mod-
P978
.
M
I
N
U
T
E
S
B
U
N
N
-
O
-
M
A
T
I
C
P
/
N
2
6
2
0
-
1
2
0
V
A
C
.
M
I
N
U
T
E
S
B
U
N
N
-
O
-
M
A
T
I
C
P
/
N
2
6
2
0
-
1
2
0
V
A
C
2
2
2
1.5
1.
5
1
1
1
.5
.5
2
.
5
2.5
M
I
N
U
T
E
S
MINUTES
M
I
N
U
T
E
S
MINUTES
M
I
N
U
T
E
S
MINUTES
P
/
N
2
4
4
8
6
-
0
0
0
0
1
2
0
V
A
C
P/N 24486-0000 120 VAC
B
U
N
N
-
O
-
M
A
T
I
C
BUNN-O-MATIC
3
3
3
4
4
5
5
6
6
7
8
2
2
2
1
.5
1.5
1
1
1
.5
.5
2.
5
2.5
M
I
N
U
T
E
S
MINUTES
M
I
N
U
T
E
S
MINUTES
M
I
N
U
T
E
S
MINUTES
P
/
N
2
4
4
8
6
-
0
0
0
0
1
2
0
V
A
C
P/N 24486-0000 120 VAC
B
U
N
N
-
O
-
M
A
T
I
C
BUNN-O-MATIC
3
3
3
4
4
5
5
6
6
7
8
S
T
A
R
T
O
N
/ W
A
R
M
E
R
S
E
L
E
C
T
O
R
R
E
A
D
Y
R
E
A
D
Y
O
N
/
W
A
R
M
E
R
S
T
A
R
T
1
1
⁄2
g
al
1
g
a
l
1
⁄2
g
a
l
S
E
L
E
C
T
O
R
1
1
⁄
2
g
a
l
1
g
al
1
⁄2
g
a
l
- 1.75 GALLON 1
- INTRODUCTION 2
- WARRANTY 2
- ELECTRICAL REQUIREMENTS 3
- Electrical Hook-Up 4
- INITIAL SET-UP 4
- INITIAL SET-UP (cont.) 5
- OPERATING CONTROLS 5
- COFFEE BREWING 5
- CLEANING 5
- TROUBLESHOOTING 6
- 27124 050800 10
- Troubleshooting 12
- WHI/GRN to Dispense Valve 13
- SERVICE (cont.) 14
- BREW SELECTOR SWITCH (cont.) 15
- 12565.0004 20
- PNK to PNK Lead from 25
- Right Brew Selector Switch 25
- Left Brew Selector Switch 25
- Wiring Diagrams 28
- RED to BLU Lead 30
- RED to BLK Wire from 30
- Terminal Block 30
- Timers (Early Models)(cont.) 37
- 27124 062100 38
- 120/208 VOLTS AC OR 44
- 120/240 VOLTS AC 44
- & ONE-GRINDER INTERFACE 47
Related products and manuals for Coffee grinders Bunn Dual TF
Coffee grinders Bunn ESJ User Manual
(6 pages)
(6 pages)
Coffee grinders Bunn LPGA-2E User Manual
(6 pages)
(6 pages)
Coffee grinders Bunn LPG LPG-2E User Manual
(22 pages)
(22 pages)
Coffee grinders Bunn CDS-3 User Manual
(60 pages)
(60 pages)
Coffee grinders Bunn WDG2 User Manual
(2 pages)
(2 pages)
Coffee grinders Bunn G9-2T HD User Manual
(20 pages)
(20 pages)
Coffee grinders Bunn G1 User Manual
(6 pages)
(6 pages)
Coffee grinders Bunn LPG-2E User Manual
(22 pages)
(22 pages)
Coffee grinders Bunn LPG User Manual
(2 pages)
(2 pages)
Coffee grinders Bunn G2 User Manual
(22 pages)
(22 pages)
Coffee grinders Bunn G9WD-RH User Manual
(15 pages)
(15 pages)
Coffee grinders Bunn CWTA-APS EN User Manual
(32 pages)
(32 pages)
Coffee grinders Bunn IMIX 14 User Manual
(17 pages)
(17 pages)
© 2020, manymanuals.com. All rights reserved. | 2.328 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals