Bunn DUAL068000 User Manual

SINGLE ® TF DBC ®W/SMART FUNNEL®DUAL®TF DBC®W/SMART FUNNEL®S/N DUAL068000 & UPPROGRAMMING MANUALBUNN-O-MATIC CORPORATIONPOST OFFICE BOX 3227SPRING

Page 10PROGRAM FLOW DIAGRAM (Cont.)PROGRAMMING THE BREWER (cont.)L BYPS OZ/M XX.X (-) DONE (+) R BYPS OZ/M XX.X (-) DONE (+)CALI

Page 11UNITSMETRIC DONE ENGCHANGING UNITSWILL!! ERASE!!ALL PREVIOUSLYSTORED RECIPESAND ALL SETUPINFO WIL BE LOST!ARE YOU SURE?YES NOSELECT

Page 12MUST GRIND INTO FUNNEL FIRST (COFFEE NAME) SETUP COMPLETE BEGIN SETUP OF (COFFEE NAME) QUIT SETUP? YES USE LEFT SIDE ONLY INSERT FUNNEL WITH NE

Page 13PROGRAMMING THE BREWER (cont.)SET NEW RECIPE (cont.)8. Using (-) and (+), set the amount of brew water, in ounces, to be dispensed for that pa

Page 14SET NEW RECIPEUsing a RECIPE CARD to load coffee names and brew settings into the SINGLE TF DBC or DUAL TF DBC with Smart Funnel: The

Page 15PROGRAMMING THE BREWER (cont.)DUALBREWERSSET NEW RECIPE:If not using a Smart Funnel (with a computer chip) and/or a G9-2T DBC or MHG Grinde

Page 16PROGRAMMING THE BREWER (cont.)REVIEW RECIPES/MODIFY RECIPES/SET UP NO NAME COFFEE FAVORS: This function has three parts. It allows the ope

Page 17PROGRAMMING THE BREWER (cont.)BREW OZ (SETTING OR ADJUSTING BREW VOL-UMES) This function allows adjustment of the brew vol-umes for eac

Page 18PROGRAMMING THE BREWER (cont.)% BYPASS This function allows adjustment of the amount of water that bypasses the grounds. The number signi-fies

Page 19SET PULSE BREW: This function allows the operator to program the brewer to "pulse” the sprayhead flow on and off during a brew cycle

Page 241342 112008BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTYBunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:1) All equipmen

Page 20SET PULSE BREW (cont.)PROGRAMMING THE BREWER (cont.)REVIEW RECIPES? NO YESEXIT TONEXT FUNCTIONSCREENNO-NAME LEFTMODIFY SHOW NEXTNO-NAMEMODIFY

Page 21PROGRAMMING THE BREWER (cont.)SET PULSE BREW - EASY PULSE SETUPNOTE: The procedure to enter the PULSE BREW function must be performed

Page 22PROGRAMMING THE BREWER (cont.)SET PULSE BREW - ENTER TIMESNOTE: The procedure to enter the PULSE BREW function must be performed prior

Page 23PROGRAMMING THE BREWER (cont.)SET PREINFUSION: This function sets the brewer to turn the sprayhead flow on for a preset time (1st ON TIME) foll

Page 24PROGRAMMING THE BREWER (cont.)DRIP TIME (now displayed on "non" funnel lock units as well) This function allows the setting o

Page 25PROGRAMMING THE BREWER (cont.)COPY SETTINGS (NO NAME COFFEE SETTINGS ONLY) This function is used on DUAL brewers only to transfer all the

Page 26PROGRAMMING THE BREWER (cont.)2. Press YES in this screen. The display should read LEFT ->->-> RIGHT. 3. If the initial programming

Page 27PROGRAMMING THE BREWER (cont.)REFILL - Range: 20 to 230 This function allows the operator to adjust the sensitivity of the refill circui

Page 28PROGRAMMING THE BREWER (cont.)SPRAY OZ/M (DUAL BREWERS) This function allows the operator to view or to enter the actual flow rate coming out o

Page 29PROGRAMMING THE BREWER (cont.)BYPASS OZ/M (SINGLE BREWERS) This function allows the operator to view or to enter the actual flow rate coming ou

Page 3TABLE OF CONTENTSGlossary ...

Page 30CALIBRATE FLOW This function allows the operator to enter the actual flow rate of the sprayhead and the bypass (for each side on DUAL brewers)

Page 31PROGRAMMING THE BREWER (cont.)CALIBRATE FLOW (cont.)Procedures to calibrate the bypass flow rate:1. Place a container, accurately graduated in

Page 32PROGRAMMING THE BREWER (cont.)BREW COUNTERS This function allows the operator to track the number of brew cycles completed. The n

Page 33PROGRAMMING THE BREWER (cont.)Procedure to test components (outputs):1. Place brew funnels into rails on both sides of brewer.2. Plac

Page 34PROGRAMMING THE BREWER (cont.)SERVICE TOOLS (cont.)NOTE: To bypass testing any component, press NEXT to advance to the next one, without testin

Page 35TEST OUTPUTS?NO YESSERVICE TOOLS?NO YESLEFT BREW VALVEON NEXT OFFLEFT BYPASSON NEXT OFFLEFT

Page 36SERVICE TOOLS (cont.)PROGRAMMING THE BREWER (cont.)the next function screen. Press YES to run tests on various components and outputs with

Page 4GLOSSARYAD CARD: An assembly consisting of computer chips and an instruction label. Used for loading advertising messages into the brewer.BREW L

Page 5PROGRAMMING Using the menu-driven display on the front of the brewer, the operator has the ability to alter or modify various brewing parameter

Page 6MAIN SCREEN This screen will be shown when the brewer is ready for use. The screen displays the water temperature in the tank. When the water i

Page 7PROGRAMMING THE BREWER (cont.)PROGRAM FUNCTIONS - LEVEL 2 There are three methods of programming the vari-ous brewing parameters of the SINGLE

Page 8PROGRAM FLOW DIAGRAMPROGRAMMING THE BREWER (cont.)Cycles thru right sideprogram constantsLEVEL 1Press upper right hidden switch for approximate

Page 9PROGRAM FLOW DIAGRAM (Cont.)PROGRAMMING THE BREWER (cont.)% BYPASS XX (-) DONE (+)3 BATCHES DONE? NO YESSET PULSE BREW NO