Bunn dual sh dbc Specifications download pdf (Page 8)

Page 8

INITIAL SETUP

CAUTION: The brewer must be disconnected from the power source throughout the initial setup, except when

speciﬁed in the instructions.

1. Insert an empty funnel into the funnel rails of one of the brew stations.

2. Place an empty server under the funnel.

3. Connect the brewer to the power source. Water will begin ﬂowing into the tank and stop when the tank is

ﬁlled to its capacity. Display will show PLEASE WAIT...TANK FILLING until tank is ﬁlled with water.

4. Wait approximately twenty minutes for the water in the tank to heat to the proper temperature. Display will

show READY TO BREW...WATER TEMP: XXX˚ when tank is at operating temperature.

5. Place a small vessel beneath the faucet and open the faucet handle. Release it when you hear the tank reﬁll-

ing.

6. Water volumes have been preset at the factory. Refer to adjustments for the Set Brew Volumes section of

this manual should the volume need to be increased or decreased.

7. The brewer is now ready for use in accordance with the coffee brewing instructions.

COFFEE BREWING

1. Insert a BUNN ﬁlter into the Smart Funnel.

2. If a grinder is not used to obtain the coffee grounds, pour the proper amount of fresh coffee grounds into

the funnel and level by gently shaking. Slide the funnel into the funnel rails and select batch size. Proceed to

step 5.

3. If a G9-2T DBC or MHG grinder is used with a compatible Smart Funnel, select the desired batch size on the

grinder. Grind the selected amount of fresh coffee into funnel and level grounds by gently shaking. It is not

necessary to select a size on the brewer.

4. Slide the funnel into the funnel rails. The brewer will read the size ground through the chip in the funnel

handle and will automatically select the correct size to brew.

5. Place an empty server under the funnel.

6. The ENABLE BREW switch must be ON. Momentarily press and release the "BREW" switch. If the brewer has

the funnel lock option and if it is activated, once a brew cycle has been started the funnel is locked in place.

There may be certain situations in which the brew cycle will not begin when the brew switch is pressed:

a) BREW TEMPERATURE TOO LOW - wait until heated or cancel BREW LOCKOUT option.

b) FUNNEL NOT IN PLACE (or using a standard brew funnel) - cancel FUNNEL DETECT option.

c) CHECK FUNNEL - remove funnel, empty previously brewed grounds and grind a new batch into funnel.

d) SERVER NOT IN PLACE - place Soft Heat Server, or cancel SERVER DETECT option.

7. If none of the above messages are displayed, the display will read NOW BREWING and the time remaining

in the brew cycle. Arrows will point to the side which is brewing. If both sides are brewing simultaneously,

the arrows will alternate from left to right on the display.

8. Following the BREW will be a countdown of DRIPPING time which shows the time remaining until the funnel

lock will release. Discard the grounds and ﬁlter only after visible dripping stops.

CLEANING

1. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all

surfaces on Bunn-O-Matic equipment.

2. Check and clean the sprayhead. Use the pointed end of sprayhead cleaning tool (#38227.0000) to remove

any mineral deposits from the sprayhead holes.

3. Insert the long end of sprayhead cleaning tool into the sprayhead ﬁtting, and rotate several times to remove

any mineral deposits from the ﬁtting.

4. Insert the short end of sprayhead cleaning tool into the bypass ﬁtting, and rotate several times to remove

any mineral deposits from the ﬁtting.

NOTE: In hard water areas, this may need to be done daily. It will help prevent liming problems in the brewer

and takes less than a minute.

29877 022509

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 48 49

Comments to this Manuals

No comments

Bunn dual sh dbc Specifications Page 8

Comments to this Manuals

Related products and manuals for Coffee makers Bunn dual sh dbc